Ribbon cartridge installation

printer ribbon cartridge nstallation

1. First printer is turned off, the front of the printer to open the transparent cover

How to install printer ribbons

2. The platen lever Gently pull

How to install printer ribbons

3. Then move the platen lever up standing

How to install printer ribbons

4. Place the print head moves to the middle to allow disassembly and installation in the ribbon cassette

How to install printer ribbons

5. The print head with one hand and hold the lower part of both ends, gently pull out

6. After removing the ribbon profile piece, hand raised portion pinch outward pull on the ribbon cartridge

How to install printer ribbons

7. You can remove the ribbon cartridge

How to install printer ribbons

8. The ribbon cartridge is surrounded by Kazi

How to install printer ribbons

9. Gently push the clip to the outside, the ink ribbon cassette lid open

How to install printer ribbons

10. After the ribbon cartridge cover is open, remove the sheet metal profile

How to install printer ribbons

Were replaced after the ribbon 11. Remove the stop plate (if the purchase is genuine ribbon, the ribbon cassette stored in the form of ribbons and ribbon storage form consistently placed immediately) and then follow the above steps to re-install the ribbon cartridge

How to install printer ribbons

12. After the ribbon is installed, install the ribbon cartridge, the distal end of the ribbon stop plate slots in accordance with the print head left and right ends of the chute can be inserted.

Ribbon Fault and Maintenance

Ribbon Fault and Maintenance
1, breaking the ribbon - a printer ribbons tension is too large, pull off the sutures or word hammer smashing ribbon cause ribbon rupture. In the former case can be broken part cut, sewn back good; the latter case, as long as you can change the ribbon.
2. ribbon is jammed - off the wire edge ribbon, easily wrapped ribbon round after fluffing led ribbon round cards, ribbons not properly retract the ribbon cartridge. The solution: First, open the printer cover, turn the ribbon discharge interlock lever arm and hammer open, end ribbon belt ribbon cassette gently back, and then close the arm with the hammer on the ribbon row interlock handle, turn on the power, the machine will be in self-test ribbon Replace the ribbon cartridge.
3, ribbon capstan drive belt worn or broken - this failure is due to drive belt or chain of characters used for too long caused friction drive belt. The solution is to adjust the position of the character chain, it is no longer friction drive belt; already broken, replace it.
4, ribbon motion sensing signal interruption - to check if ribbon motion sensor signal line has been damaged, if broken, replace the signal line; then check the interlock signal conversion board Ribbon motion sensing line at J6 socket whether damaged or not, replace or plugged signal lines

Printing ribbon is not installed

In addition, there is a need to remind you note is a frame of built-in two gear must be the ribbon with, but also to ensure that keep parallel with them, or else gear to move the ribbon will move to the ribbon shift phenomenon, finally will jam the gear to the normal ribbon cannot be turned. When, in accordance with the above method after the ribbon is installed, we must also be in accordance with the original installation method will print reinstall back to printer, finally will be the top of the printer cover again in situ, so the ribbon change process even over.
Printing ribbon is not installed, replace, can ensure ideal printing effect, we must be the same with toner or cartridge protection to protect the good ribbon, to both improve the print quality and prolonging the service life of the ribbon. Of course, to protect the ribbon, some appropriate skills must be mastered, it's not some details of the following skills, will make everyone get it!
To familiar with the paper thickness regulator, to ensure that the print head and the distance from the surface of the printing paper always are in the right. Under normal circumstances, when the printer is using a new ribbon, that we can by adjusting the thickness of the paper regulator, the distance to the print head and paper surface slightly widened, so that you can avoid printed handwriting effect is too strong, which can effectively ensure the quality of printing; If printing ribbon, have been used for a long time, and print the current page text seems to have less clear than before, so we can try to adjust the paper thickness regulator, the distance to the print head and paper surface slightly closer and so can the ribbon "potential" dig out as much as possible. Under normal circumstances, we are adjusting the paper thickness regulator, should be to ensure that the printing effect can meet our needs under the premise of fully follow the principle of can is big. In other words this time, stylus printer can't completely quit the historical stage, and in ink jet printers and laser printers a dime today, instead of the role and status of the stylus printer appears more important and highlighted.