Printing ribbon is not installed

In addition, there is a need to remind you note is a frame of built-in two gear must be the ribbon with, but also to ensure that keep parallel with them, or else gear to move the ribbon will move to the ribbon shift phenomenon, finally will jam the gear to the normal ribbon cannot be turned. When, in accordance with the above method after the ribbon is installed, we must also be in accordance with the original installation method will print reinstall back to printer, finally will be the top of the printer cover again in situ, so the ribbon change process even over.
Printing ribbon is not installed, replace, can ensure ideal printing effect, we must be the same with toner or cartridge protection to protect the good ribbon, to both improve the print quality and prolonging the service life of the ribbon. Of course, to protect the ribbon, some appropriate skills must be mastered, it's not some details of the following skills, will make everyone get it!
To familiar with the paper thickness regulator, to ensure that the print head and the distance from the surface of the printing paper always are in the right. Under normal circumstances, when the printer is using a new ribbon, that we can by adjusting the thickness of the paper regulator, the distance to the print head and paper surface slightly widened, so that you can avoid printed handwriting effect is too strong, which can effectively ensure the quality of printing; If printing ribbon, have been used for a long time, and print the current page text seems to have less clear than before, so we can try to adjust the paper thickness regulator, the distance to the print head and paper surface slightly closer and so can the ribbon "potential" dig out as much as possible. Under normal circumstances, we are adjusting the paper thickness regulator, should be to ensure that the printing effect can meet our needs under the premise of fully follow the principle of can is big. In other words this time, stylus printer can't completely quit the historical stage, and in ink jet printers and laser printers a dime today, instead of the role and status of the stylus printer appears more important and highlighted.

Needle type printer ribbon fault

1, the ribbon fracture
Tensile strength of the ribbon is too big, snap sutures or hammer smashing the ribbon ribbon fracture cause. Former broken part can be cut and sewn back; The latter case as long as change the ribbon.
2, the ribbon was stuck
The edge of the ribbon easily entangled epson printer ribbon  ound after take off a silk, burr, led to the card and ribbon round the ribbon not retract properly foil box. The solution is: first, open the printer cover, transfer ribbon arm interlock with hammer handle to open, the ribbon on the ribbon box to send belt end back gently, and then close the ribbon jib to interlock with hammer handle, open the power supply, machine ribbon will comes back after self-checking foil box.
3, damage of hall effect
Ribbon cassette, frequently hall effector squeezed continuously, causing the damage fracture. This kind of failure can only replace the ribbon derrick assembly or use the compatible olivetti printer ribbon motion sensor replacement.
4, the active wheel drive of ribbon belt wear or fracture
This failure is due to the driving belt use time is too long or character chain caused by friction drive belt. The solution is to adjust the position of the character chain to make it no longer friction driving belt; Has been broken, please replace.
5, ribbon movement sensing signal is interrupted
First check to see if the ribbon movement sensing signal lines has been damaged, if broken, please replace signal lines; To check the interlock switch board J6 socket in the ribbon movement sensing signal whether damaged or contact is not good, please replace or good signal lines.

Needle printer

Needle type printer is a special kind of printer, and ink-jet, laser printers are there is a big difference, and this difference needle type printer are other types of printers can not be replaced, it is precisely because of this, needle type printer always have their own unique market share, in the service of some special industry users.

Needle type printer in the print head is through 24 needle hit the carbon paper, thusforming a font, in use, the user can according to the demand to select multiple paper,commonly used multiple paper 2 joint, 3 joint, 4 joint papers, which have also used the6 associated printer paper. Multiple paper disposable needle type thermal transfer printer ribbon printer can onlyprint finished quickly, ink jet printer, laser printer is unable to realize the multipleprinting paper.Basic ----1964 years, Olympiad held in tokyo. At that time, responsible for providingtiming products Epson Corp especially developed crystal chronometer 951 and printtype chronograph. These two products are not only at the time to shine, but also for the future company transformation and Printer ribbon diversification brought profound R & D base and opportunity. Development - the world's first PC with mainstream needle type printerIn 1978, Epson Corp issued a needle type printer (7 pin) TP-80, product well received. In 1980, MP-80 (pin 9) published, also caused a sensation in the world,second years, MP-80 in the Japanese market share as high as 60%, in USA marketalso received high evaluation, gradually become the mainstream of the world's firstneedle type printer for PC products.

The thermal transfer ribbon type

To adapt to the different was printed materials and durability requirements, thermal transfer ribbons according to the coating materials can be divided into the wax, wax / resin mixture base, resin three.

A) wax: usually has a high density, the degree of Gao Min, used paper labels, printingeffect is good, the cost of economic.

Universal type wax based thermal transfer printer ribbon refill is applicable to most of the thermal transfer printer, in the case of low power consumption, high sensitivity can still achievethe ribbon printing density and definition of excellent print speed of up to 200mm/s.Heat resistance: 100 DEG C, print material: coated paper, coated paper, the melting point of 65 DEG C. Enhanced wax based thermal transfer ribbon print speed of up to 250mm/s. The melting point of 80 DEG C.

B) mixed base: both high-quality printing effect and durability, wide application, goodprice effect.

Wax / tree mixed base ribbon has the emotional Gao Min: consumption, delay the printhead life. Heat resistance: 100 DEG C, the printing speed: 250mm /s, print material: coated paper, coated paper, PVC, PET, PE, PP, melting point of 75 DEG C. Side pressure enhanced wax / tree mixed base ribbon printer is applicable to edge type printer,are compatible with many label paper, and has anti fouling characteristics of scratch.Print speed: 300mm /s, the melting point of 80 DEG C.

C) resin matrix: most durability, abrasion resistance, heat resistance, corrosion resistance, some formula can prevent steam pressure, some were able to washing ordry cleaning

Enhanced resin thermal transfer ribbon is suitable for flat type print head, in the case of low power consumption, print speed of up to 200mm/s. print resolution up to 200DPIto 300DPI. Heat resistance: 100 DEG C, the printing speed: 200mm/s, PVC, PET, printmaterials: PE, PP, melting point of 80 DEG C. Side pressure reinforced resin ribbon is applicable to edge type printer. In the case of low power consumption, unique back coating technology, make the printing more flexible easily, even do 90 degree rotationprinting. Heat resistance: 180 DEG C, the printing speed: 200mm/s, melting point of 80 DEG C:

The technical index of the thermal transfer ribbon

A, transfer refers to the ink ribbon layer transfer to the percentage of the print medium, ink layer whether 100% fully heat transfer to the print media (plastic, paper,composite film and other material), transfer percent much ink.

B, adhesion refers to ink layer print to print media (plastic, paper, composite film and other material) on adhesion fastness and abrasion degree.

C, definition refers to the ink layer heat transfer to the printing medium, print out thetext clear degree, whether or not beautiful.

D, adaptive to thermal transfer Compatible epson printer ribbons can be in various media (plastic, paper,composite films and other materials) and the production environment (cooking,freezing etc.) in printing, the printing effect can meet the requirements of customers.

E, temperature of thermal transfer ink fax ribbon in the use of process temperature,thermal transfer ribbon characteristics of different causes in actual use temperature is not the same, in different temperature printing effect is also different, only the best printing results, temperature is the best.

The application field of the thermal transfer ribbon and the principle of work

Thermal transfer ribbon is a very wide range of uses, the amount is very huge products. With the development of information technology in China and rapid development of computer application domain unceasing expansion and in-depth, people of high speed, high quality output print demand more and more, and the traditional way of printing market in terms of price, printing quality, printing speed is difficult to meet the user needs in all directions. Thermal transfer Epson printer ribbon dfx8000/5000  ade of high strength thin films due to the high concentration and ink, and the use of single use mode, so the characters of high quality printing, STAR printer ribbon  nd long service life, but also overcome the ink feathering, easily soluble in water and other defects, thermal transfer printing method to print medium without any requirements, can be in plain paper, recycled paper, waxed paper, ordinary film, envelopes, paper label until the cloth to achieve high clear print.

Thermal transfer imaging method was invented by Mille in 1953, along with the development of microelectronic technology, lithography technology, the semiconductor electric heating element technology and laser technology, especially the development of high sensitivity thermal transfer imaging function of material technology, thermal transfer printer as a non-contact printing computer peripherals hard output devices, has become a market share special kind of printer of high rate. The imaging principle of thermodynamics is heat transfer to the imaging material support body through computer signals to drive the semiconductor electrothermal head or laser, the imaging material heat melting and transferred to the text and image by image forming medium. Thermal transfer imaging material is coated on the base tape, called thermal transfer ribbon or thermal transfer ribbon.

Introduction and basic structure of thermal transfer ribbon

Thermal transfer ribbon called hot foil stamping ribbon, referred to as the ribbon,English is Thermal Transfer Ribbon.

Thermal printing ribbon is printer supplies, is on the side of a base coated with wax,resin or mixed ink polyester or other high density film. In the absence of ink coated on one side with a lubricant to prevent wear and damage to the print head, a commonshaft core TTR printer ribbon with paper and plastic two, the main requirement is not deformationand not in print slide. Common ribbon with wax, wax tree based mixed base, resin based several. China, use of the IBM printer ribbon are common date code Tandai, infusion bagribbon, washing cloth, special resin ribbon cable with ribbon, barcode ribbon, wax -ribbon, mixed base - ribbon, ribbon and other kinds of resin matrix - type. Different materials and varieties of ribbon / ribbon for printing materials and printers have different applicable in thermal transfer ribbon, ribbon / technology, printerperformance is the primary.

A) thin but strong polyester or other high density material with base;

B) bottom coating with matrix positive to ensure that the ink evenly and printing inktransfer complete;

C) ink layer of wax or resin base;

D) outer coating layer on the printing ink in ink and enhanced protection andadhesion of printed material;

E) back coating base with anti-static, both heat and reduce friction, in order to protect the print head.